Information

 

 

They are making several good points regarding Installing A Bathtub overall in this article underneath.

Installing a bath tub isn't exactly rocket science, however it does need strong plumbing, carpentry, and occasionally, tiling skills. Changing an old tub with a new one is additionally a moderately hard job. If the old bathtub is easily accessible, the job can relocate immediately; if you have to open up a wall to eliminate the old bathtub and place the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need an assistant to vacate the old tub and also set in the new one. See to it you have certified on your own for the task and also are comfortable attempting it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration using one before you begin. Opportunities are you may need an expert plumber to make tube links.
This article will aid you mount a new tub in your restroom if you have actually currently bought a new tub and also do not need to change the plan of your previous water pipelines.
Your tools and material list need to comprise the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Removing Old Taps

If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, switch on the faucets to drain any type of water remaining in the system. The process of removing the existing taps can be fairly bothersome as a result of the limited gain access to that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will come from the pipelines. As soon as the supply pipelines have been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to carrying on to fit the new faucets, contrast the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.

 

 

Fitting New Touches

If the tails of the new taps are plastic, after that you will require a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap and the various other end gives a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making certain that the washers are in area between the faucet and the sink. Safeguard the faucet in place with the supplier supplied backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical tap ports. The previous type needs to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.

 

 

Setting up the Bathtub

Making use of the two wood boards under its feet, place the bath tub in the required placement. The wooden boards are handy in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to make certain that the tub is leveled all round. This can be attained by examining the spirit level as well as readjusting the feet on the bathtub until the spirit level reviews degree.
To install taps, fit all-time low of the outermost flexible tap connector to the suitable supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water supply as well as inspect all joints and also brand-new pipework for leaks and tighten them if required. Fill up the bath tub as well as additionally check the overflow outlet as well as the typical electrical outlet for leakages.
Lastly, deal with the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the tub must wait till the bathtub has been utilized at least when as this will certainly resolve it into its final setting.

 

 

Getting ready for the Installment

To start with, the supporting frame supplied with the bathroom must be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its final placement.

 

 

Tiling Around the Tub

In the location where the bathroom meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall between the bathroom as well as the tiling, leading to issues with dampness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not think about this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or waterproof glue and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I'm just very fascinated with How to Install a Bathtub Yourself and I hope you enjoyed reading the post. Enjoyed our piece of writing? Please share it. Help someone else discover it. Thanks for your time. Visit again soon.

Click For More Information